Kunena Site Syndication http://www.estadrags.com Tue, 21 May 2013 19:42:14 +0000 Kunena 1.6 http://www.estadrags.com/components/com_kunena/template/default/images/icons/rss.png http://www.estadrags.com/ en-gb http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2853-wtb-70-72-monte-carlo-trans-crossmember#2853 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2853-wtb-70-72-monte-carlo-trans-crossmember#2853
315-395-1973 Adam]]> Engines, Parts & Stuff Sun, 19 May 2013 21:20:35 +0000 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2853-wtb-70-72-monte-carlo-trans-crossmember#2853 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2841-1969-300hp-350-and-th350#2841 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2841-1969-300hp-350-and-th350#2841
Great engine and trans for a stocker or a restoration. $1,200 for both.

315-395-1973 Adam]]> Engines, Parts & Stuff Fri, 10 May 2013 19:35:35 +0000 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2841-1969-300hp-350-and-th350#2841 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2835-sbc-g-body-headers#2835 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2835-sbc-g-body-headers#2835
315-395-1973 Adam]]> Engines, Parts & Stuff Mon, 06 May 2013 20:27:40 +0000 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2835-sbc-g-body-headers#2835 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2831-mopar-stuff#2831 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2831-mopar-stuff#2831 8" convertor came with my cuda,for 727 do not know much about $250
manual steering box for b-body may work in others,have part # $150
weld draglite rims 14" 8"back space duel pattern with 14.5x32 slicks and tubes,$500pr
8 3/4" suregrip 4.10 gears 742 case, $450
weld pro stars 7" 5" back space,4 1/2" x 5 $150pr
dana 4.88 gears $100
315 529-4082 thanks howard]]> Engines, Parts & Stuff Sun, 05 May 2013 18:18:38 +0000 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2831-mopar-stuff#2831 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2824-358-sbc-w-tunnel-ram#2824 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2824-358-sbc-w-tunnel-ram#2824 Engines, Parts & Stuff Wed, 01 May 2013 19:57:10 +0000 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2824-358-sbc-w-tunnel-ram#2824 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2820-malibu-parts#2820 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2820-malibu-parts#2820 bgreer@cogeco.ca i only live in kingston ont]]> Engines, Parts & Stuff Sat, 27 Apr 2013 01:05:41 +0000 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2820-malibu-parts#2820 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2814-grudgeoutlaw-406-sbc-nitrous-motor#2814 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2814-grudgeoutlaw-406-sbc-nitrous-motor#2814

- Block casting number is GM 3951509 bored .030
and half filled
- Pro Series 3.75" crank - Oliver 6" Rods
- gas ported Weiseco pistons - 14:1 compression
- Hellfire gapless rings
- Milodon billet splayed caps
- All-Pro 220cnc heads - 58cc chambers - rolled
to 18 degree with Harland Sharp roller rockers and
stud girdles
- conventional 23 degree standard pattern headers fit
- was run previously with custom 2 to 2 1/8" stepped
headers when sprayed last
- flow numbers were spec'd at .700 lift with 28" of
water - 318.75 intake 257.85 exhaust ( factory specs
- they have been freshened at least once since then
- may have additional port work done - and may have
been shaved at that time)
- the Brodix HV1 intake was spec'd to match (4500
flange - no adaptor plate)
- fresh rebuilt 1150 Dominator carb - with receipt -
no fuel has been in it
- custom ground nitrous roller cam
(700+ lift on a 114 lobe center)
- has not been sprayed since freshening
- maybe 20 N/A passes ( mid 6's in the 1/8 ) (low 10's
in the 1/4) in an all steel 2nd gen camaro with a
Powerglide, 5500 stall and 4.88 gears
- deadly consistant bracket racing engine N/A and
cools quicker than any motor I've seen
- I never got the funds together to get all the
neccessary parts to spray it safely
- I'm told it went 7.90 in the 1/4 on a fogger in a
NMCA 10.5 Outlaw Camaro with it's previous
owner
- engine builder said it made 738hp on motor alone
and was built to handle multiple stages totaling 600
hp of spray
- Cold Fusion plate system shown is not available
- it is not mine to sell
- please note - I do not have any build sheet or dyno
sheet for this engine - there was none available
when I bought it - I will be happy to remove covers
for inspection - but I will not disassemble it - it
is currently fogged and in a cradle for winter storage

$4500 obo all reasonable trades will be considered
Phone Number: (607)237-4316 Matt]]> Engines, Parts & Stuff Tue, 23 Apr 2013 21:16:08 +0000 http://www.estadrags.com/component/kunena/7-engines-parts-a-stuff/2814-grudgeoutlaw-406-sbc-nitrous-motor#2814